CloningofsmallRNAswith5’phosphateand3’OHends3

Quantification of small RNA PCR products.

1. Mix 1 μl of the resuspended small RNA PCR product with 2 μl of water for nanodrop determination. Do the same with 1μl of resuspension buffer + 2μl of water for the blank. 
   
   

2. Take the following Nanodrop readings. Remember that your sample is a 3X dilution, so multiply the final concentration by 3. 
   
   
   
   

• 230

• 260

• 280

• 260/280 (want 1.8 for pure DNA)

• 260/230

• ng/μl (see section "Materials & Reagents" for correction factor used for the Pellet Paint)

3. Mix 1 μl of your PCR product with 4 μl water and 5 μl DNA loading dye. Run your samples on a 10% native gel along with 0.5 μg (5μl of the dilution) of the 100bp Generuler Fermentas Ladder. If 0.5μg (5μl) is loaded, the 100bp band is 40 ng. Use the Quantity One software to determine the concentration of your PCR products.

4. Take an average reading between the nanodrop and the BioRad quantification. You will use this number to determine the Molarity of your library (comment 6).

5. Determine the molarity of your library 
   
   

• Size of cloned small RNAs (average is 93bp for Arabidopsis small RNAs)

• Molecular mass = 93bp x 650 = 60450

• 60450 g = 1 mol or 60450 μg = 1 μmol

• Concentration of library in μmol/ml = [ng/μl]/60450

  i. Example, if PCR product is 16ng/μl. The concentration of the library is 16/60450 = 0.000264 μmol/ml = 0.264 μmol/L or 264nM

Back to top

Materials & Reagents

Back to top

Author Notes

1. Adapter specifications used in the Baulcombe lab. Please note, the sizes used in this protocol are based on the sizes of the adapter molecules and PCR primers. If you use primers/adapters of other sizes, then you need to adjust the sizes cut out of the gels accordingly.

• 5’ RNA adaptor = 26bp of an RNA:DNA hybrid molecule. The three 3’ bases are RNA and the rest is DNA (ordered through Dharmacon). We dephosphorylated before use.

• 3’ RNA adaptor = 23bp of RNA/DNA hybrid molecule. The 5’ base is phosphorylated. The three 5’ bases are RNA the rest is DNA. The 3’ end of the of the adapter has an inverted thymine moiety (iDT) (ordered through Dharmacon)

• Small RNA RT-primer: DNA oligo complementary to the 3’ adapter

• Small RNA PCR Primer 1: identical to the RT primer

• Small RNA PCR Primer 2: We use a DNA oligo 44bp long that incorporates the 5’ adapter but adds a tail at the 5’ end to increase the length of the PCR product.

Back to top

Reviewer Comments

Reviewed by: Eric Miska, Gurdon Institute, Cambridge

1. We use mirVana kit followed by gel purification. This allows precise size selection of small RNAs by preventing any smears from overloaded lanes on the gel.

2. Alternatively, the Criterion system can be used. We find it most important to exclude any cross-contamination of samples at this point. One sample per gel would be ideal.

3. We find eluting from an intact gel slice as effective and easier to handle. It is important to prevent any gel “bits” to be included in the precipitation step.

4. We find it useful to pick colonies onto a rectangular agarose plate in an 8x12 grid. We the set up the PCR reactions using a 96 well replicator. Positive clonies can then easily be identified for sequencing.

5. More than 17 cycles will likely just result in empty amplification: you will get many identical reads instead of increased sequencing depth.

6. As concentration is absolutely critical, it would be useful to check samples additionally on a BioAnalyzer.

Back to top

Figures

Figure 1. Overview over the flow of the cloning procedure